Domestic UPS
PL8150 -1KVA to 3KVA
The line-interactive UPS uses a totally different design than any type of offline UPS. In this type of unit, the separate battery charger, inverter and source selection switch have all been replaced by a combination inverter/converter, which both charges the battery and converts its energy to AC for the output as required. AC line power is still the primary power source, and the battery is the secondary.
Application
Suitable for Personal Computers, DeskJet Printer, Television, Fan, Tube light, CFL, Iron, hand mixer etc.
How it is different from the products of other manufacturer
Closed Loop Auto Sensing Software Control (ASSC) Smart Battery Charging Technology for longer battery life.
Health monitoring indication (LED) ‘UPS OK’ on the bezel of UPS.
Intelligent Thermal Management System : Programmed Inbuilt cooling fan which operates as needed with UPS thermal protection to prevent undue loss of energy.
Features
Advanced DSP based technology for absolute and stable sine wave output.
LED indications for Mains ON, UPS ON, Batt Low, Charging, Over Load, UPS OK
Dual Mode of working : UPS and Normal
- UPS Mode : Fast switching, Input operating range from 180V to 260V
- Normal Mode : Wide Input operating range from 100V. to 280V
Closed Loop Auto Sensing Software Control (ASSC) Smart Battery Charging Technology for longer battery life.
Dual selectable charging current option for Normal Charging and High Charging.
Intelligent overload sensing circuitry with auto retries facility.
Programmed Inbuilt cooling fan which operates as needed with UPS thermal protection.
High Power new generation MOSFET capable to handle high in-rush/ surge current.
Indicate the health of UPS on the bezel as ‘UPS OK’.
Highest efficiency at lower cost.
Technical Specifications
| Capacity | 650 VA | 850VA | 1050VA | 1450VA | 2000VA |
| Nominal Voltage | 12VDC | 12VDC | 12VDC | 24VDC | 24V/36VDC |
Ac Mains Mode
| Input Voltage Range (Normal Mode) | 100 to 280 VAC ± 5 VAC |
| Input Voltage Range (UPS Mode) | 180 to 260 VAC ± VAC |
| Changeover Time Maximum | <=30 ms |
| Max. Charging Current (NC) | 9A ± 1A |
| Max. Charging Current (HC) | 12A ± 1A |
| Boost Charging Voltage | 14.4 ± 0.2 VDC |
| Float Charging Voltage | 13.7 ± 0.2 VDC |
Battery Backup Mode
| Output Voltage at No Load | 220 VAC ± 7 VAC |
| Output Frequency | 50.0Hz ± 0.5Hz |
| Output Wave Form (At No Load) | 100% Pure Sine Wave |
| Battery Low alarm | 10.6 ± 0.2 VDC |
| Battery Low protection | 10.4 ± 0.2 VDC |
LED Display
- Mains On
- UPS On
- Overload
- Charging
- UPS OK
Protection
Battery Voltage Low (4 Auto Retries), Over Load (6 Auto Retries), Battery full Charge, Over Temperature, short circuit
So, what are you waiting for?
Office UPS
PL8150 -1KVA to 3KVA
The line-interactive UPS uses a totally different design than any type of offline UPS. In this type of unit, the separate battery charger, inverter and source selection switch have all been replaced by a combination inverter/converter, which both charges the battery and converts its energy to AC for the output as required. AC line power is still the primary power source, and the battery is the secondary.
PL8150-HF 1KVA~3KVA online UPS is an on-line double-conversion UPS with input power factor correction (PFC), output power factor 0.8 offering high levels of reliability and protection for critical servers and data processing IT systems. Besides sufficient runtime as backup power, PL8150 UPS (long time model) can be fitted with matching battery extension packs for long runtime applications; besides some standard features of normal UPS, it is also able to bear wide input voltage in harsh environment, and optional N+X redundancy parallel function is also available.
PL8150 -1KVA to 3KVA
Suitable for Group of computers,Servers,Swtiches And Security systems….etc
Features
- High frequency and true double-conversion
- DSP (Digital Signal Processors) technology
- Input power factor correction (PFC)
- Wide input voltage range (110V ~ 300V)
- Output power factor 0.9
- Cold start
- Auto sensing frequency
- ECO mode operation for energy saving
- Selectable output voltage via LCD
- Output bypass settable via LCD
- Power-on self test
- Advanced battery management (ABM)
- Short circuit and overload protection
- Automatic charging in OFF mode
- Auto control fan speed when loads varies
- Standard RS232 communication port and RJ45 protection
- Optional USB / SNMP communication port
- Optional emergency power off (EPO)
- Optional extension battery bank
- Optional built-in isolation transformer
Technical Specifications
| Model | IKVAS | IKVAS | 2KVAS | 2KVAH | 3KVAS | 3KVAH | |||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Rated Capacity | 800W/1000VA | 1600W/2000VA | 2400W/3000VA | ||||||||||||||||||
| Input | Input | Single phase and Earthing | |||||||||||||||||||
| Voltage Range | 115V±5VAC – 295V±5VAC | ||||||||||||||||||||
| Frequency Range | 46Hz-54Hz@50Hz / 56Hz-64Hz@60Hz | ||||||||||||||||||||
| Power Factor | ≥0.98 | ||||||||||||||||||||
| Bypass Range | (176±5 – 255±5) VAC (Adjustable) | ||||||||||||||||||||
| Current Harmonic | <15% (100% Non Linear Load) | ||||||||||||||||||||
| Output | Output Style | Single phase and Earthing | |||||||||||||||||||
| Rated Voltage | 208VAC/220VAC/230VAC/240VAC | ||||||||||||||||||||
| Power Factor | 0.8 | ||||||||||||||||||||
| Voltage Precision | ±2% | ||||||||||||||||||||
|
|
||||||||||||||||||||
| Crest Ratio | 3:1 | ||||||||||||||||||||
| Transfer Time | Mains to Battery – 0ms | ||||||||||||||||||||
| Mains to Bypass <4ms | |||||||||||||||||||||
|
|
||||||||||||||||||||
|
|
||||||||||||||||||||
| Output Voltage Distortion | ≤ 3% (100% Linear Load) | ||||||||||||||||||||
| ≤ 5% (100% Non Linear Load) | |||||||||||||||||||||
| Battery | Input Battery Voltage |
|
|||||||||||||||||||
| Internal Battery Capacity |
|
||||||||||||||||||||
| Internal Battery Type | 12V/7Ah Sealed Lead Acid Maintenance free Battery (only refers to standard UPS) | ||||||||||||||||||||
| Backup Time | Full Load ≥ 4min (As for long backup UPS, the backup time is determined by the capacity of battery | ||||||||||||||||||||
| Charge Current (A) |
|
||||||||||||||||||||
Work Environment
| Model | 1kVA to 3KVA |
| Temperature | 0◦C to 40◦C |
| Relative Humidity | 0 to 95% non condensing |
| Altitude | < 1500m when>1500m,lower the rated power for use |
| Store Temperature | -25◦C to 55◦C |
Mechanical Specification
| Model | Battery Voltage | Dimension W*D*H (mm) | Net Weight/Gross Weight (Kg) |
|---|---|---|---|
| 1KVAS | 24VDC | 144*400*215 | 9.7/10.7 |
| 36VDC | 13-Dec | ||
| 1KVAH | 24VDC | 5.6/6.6 | |
| 36VDC | 5.8/6.8 | ||
| 2KVAS | 48VDC | 191*469*339 | 20/22 |
| 72VDC | 24.5/26.5 | ||
| 96VDC | 28.5/31 | ||
| 2KVAH | 48VDC | 11.4/13.4 | |
| 72VDC | 11.4/13.4 | ||
| 96VDC | 11.4/13.4 | ||
| 3KVAS | 72VDC | 24.6/26.6 | |
| 96VDC | 29/31.5 | ||
| 3KVAH | 72VDC | 11.6/13.6 | |
| 96VDC | 11.9/13.9 |
Communication Interface -RS232 Communication
So, what are you waiting for?
Industrial UPS
1 KVA to 5 KVA -1 phase input & 1 phase output
Features
- MOSFET/ IGBT Design
- Double Conversion Technology
- High Frequency PWM Based Inverter
- Using MOSFET IGBTs
- Auto Re-Transfer Static Switch
- Control Panel with LCD Display
- Intelligent Battery Management
- Energy Saving Mode
Technical Specifications
Online UPS 1 Phase input 1 phase output
| Capacity(KVA) | 1/2 | 3/5 | 5/7.5/10 |
| INPUT | single | single | single |
| Voltage Range | 230V, +/- 20% in single phase | ||
| Power factor | at 0.8 TYPICAL | ||
| Frequency | 50Hz +/- 3Hz | ||
| OUTPUT | single | single | single |
| Voltage / Ragulation | 230, +/- 1% single Phase | + | |
| Full Load Current | Rated at 0.8 P.F | ||
| Nominal Frequency | 50Hz +/- 0.5Hz | ||
| Power factor | 0.8 P.F | ||
| Over Load | 125% for minute & 150% for 1 minute | ||
| Static Voltage Regulation | + / – 6% for 50% step load change | ||
| Wave Form | Sinusoidal | ||
| Total Harmonic Distortion | For linear load < 2.5 % for Non-linear load < 5% | ||
| Crest Factor | 4.1 | ||
| Inverter Efficiency | 85% to 95% on full load depending on capacity | ||
| DC CHARACTERISTICS | |||
| Nominal Float Voltage | 48V | 72V | 72/120V |
| Recharge Time | 6-7 Hrs For 90% Recover | 8 – 10 Hrs for 100% Recover | |
| By Pass (Optional) | Manual / Static | ||
| PROTECTIONS | |||
| Charge | Input circuit breaker, Charger over voltage, Charger over current | ||
| Battery | Battery low cut off / Current limit, HRC fuse, Battery over charger trip | ||
| Inverter | Output over voltage / Over load trip, Current limit, Short Ckt | ||
| INDICATIONS / DISPLAY | |||
| Indications | Manis ON, Charger ON, Battery low, Inverter ON, Fault / Trip, Phase R.Y.B. presence | ||
| Display | LCD Display to indicate Output voltage, input voltage, DC voltage, load Percentage, Frenquency | ||
| ENVIRONMENTAL / OPTIONS | |||
| operating Temperature | 0 deg to 40 deg | ||
| Relative Humidity | 95% Non-Condensing | ||
| Max Operating altitude without derating | 7500ft. / 2285 m | ||
| Acoustic noise | <60db | ||
| Options | PF Correction / Remote Display / Control Software / SNMP Compatibility | ||
Due to Continuous development in technology & Design , the Specification without notice
Custom made UPS systems are manufactured as per request.
So, what are you waiting for?
Static UPS
DSP Sine Wave Static UPS (1In- 1Out)
Sophisticated and critical industrial equipments and systems must not be left to face power problems. When connected with uneven power output, you are exposing your appliance to danger where they are mostly encounter with problems as sags, surges, noise, brown outs, black outs etc.
In an industry you are required to keep electricity consumption as low as possible by ensuring that there is no interruption in the operation as well. Kondaas DSP Sine Wave Static UPS is specialized in providing clean and stable power supply to all connected appliances and equipments. We have developed our DSP Sine Wave Static UPS on world’s most advanced technology known as DSP.
Application
Suitable for Personal Computers, DeskJet Printer, Television, Fan, Tube light, CFL, Iron, hand mixer etc.
- Major power Back up source in corporate offices as well as Call Centers
- Computer & peripherals /office Equipment like, Scanners, Printers, Fax Machine etc.
- Emergency & Mobile Power Systems
- A.C and all Compressor Based Applications
- Petrol/Diesel Dispensing(Filling) Machines
- Thread Mills & other Health Equipment in Homes/Gyms
- Water Pumps and similar Motor Based Applications
Features
- State of the Art MOSFET/IGBT Based PWM Technology to increase Crest Factor
- Auto Sense Intelligent Control Smart Charger
- Electronic change- over, hence much better reliability
- Quiet of AC motors as well as other inductive loads unlike the noise that emanates from modified Sine Wave Systems
- Very low Total Harmonic Distortion < 3%
- Fast Changeover ensuring Compatibility with Computers
- TDR(Time Delay Relay), especially for AC compressor based applications
- Mains Mode Short Circuit Protection
- Surge Load Capacity up to 300%
- Less Operating Coast as compared to that with Online UPS as well as DG Sets
- Bypass Switch in case of system failure
- Compatibility with D.G Sets
- These Static UPS’s can be integrated with solar power to charge the batteries by using external solar charge controllers.
Product Range
| Capacity | 2KVA | 2.5KVA | 3KVA | 3.5KVA | 5KVA | 7.5KVA | 10KVA | 12KVA |
| Nominal Voltage | 24VDC | 36/48 VDC | 48 VDC | 48 VDC | 48/96 VDC | 120 VDC | 180,192 VDC | 192 VDC |
Ac Mains Mode
| Input Voltage Range (Normal Mode) | 100 to 280 VAC ± 5 VAC |
| Input Voltage Range (UPS Mode) | 180 to 260 VAC ± VAC |
| Changeover Time Maximum | <=30 ms |
| Max. Charging Current (NC) | 9A ± 1A |
| Max. Charging Current (HC) | 12A ± 1A |
| Boost Charging Voltage | 14.4 ± 0.2 VDC |
| Float Charging Voltage | 13.7 ± 0.2 VDC |
Battery Backup Mode
| Output Voltage at No Load | 220 VAC ± 7 VAC |
| Output Frequency | 50.0Hz ± 0.5Hz |
| Output Wave Form (At No Load) | 100% Pure Sine Wave |
| Battery Low alarm | 10.6 ± 0.2 VDC |
| Battery Low protection | 10.4 ± 0.2 VDC |
Multi Color LCD Display Colors
- Yellow Color : For Inverter/ UPS mode. No AC Mains (Utility Power)
- Green Color : When AC mains (Utility Power) is available
- Red Color : In case of any Abnormal Condition
Displaying Parameters
AC mains voltage
O/P Load in %
Battery input voltage
Battery Charging/ Discharging current (Batt. Bar)
Faults Status
- Overload
- PV Reverse
- Short Circuit
- Fuse Trip
- Over Temp (Thermometer)
- Low Battery (Empty ‘Battery’ Blinking)
Inverter Status
Solar availability Status
So, what are you waiting for?
Solar Hybrid UPS
LOW POWER SOLAR HYBRID INVERTER
Solar Energy is a best alternative energy solution. The visible light from the SUN (Solar energy) can be converted into electric energy by Photovoltaic Cells. It has potential to cater the emerging needs of the power throughout the world. Solar Hybrid Inverters are cost effective and easy to install.
KONDAAS True Hybrid Solar Home UPS is the most innovative and advance UPS that runs both on solar power (generated through solar panels) and the utility (grid) power supply. KONDAAS True Hybrid Solar Home UPS is the advanced solar hybrid home UPS which charge the battery thru readily available solar energy/ Mains by using it’s artificial intelligence. It’s ISSRC logic use Solar Power for its maximize utilization to empower homes.
Application
Suitable for Personal Computers, DeskJet Printer, Television, Fan, Tube light, CFL, Iron, hand mixer etc.
How it is different from the products of other manufacturer
Closed Loop Auto Sensing Software Control (ASSC) Smart Battery Charging Technology for longer battery life.
Health monitoring indication (LED) ‘UPS OK’ on the bezel of UPS.
Intelligent Thermal Management System : Programmed Inbuilt cooling fan which operates as needed with UPS thermal protection to prevent undue loss of energy.
Features
- Operate on both Solar Power as well as Grid Power.
- It is integrated with in-built fully regulated PWM/MPPT* Solar Charge Controller for max. Solar Power utilization.
- It senses the availability of solar power, grid power and accordingly gives preference to charging thru solar power and switches to the grid power if the solar power is not available.
- It is designed to give you maximum benefit from the solar energy and minimize your electricity bill drastically.
- Highly efficient battery charging from the solar energy as a result you will get non-stop power, save money, save electricity and protect the environment.
- Advanced DSP based technology for absolute and stable and 100% pure sine wave output.
- Indications for Mains ON, UPS ON, Batt. Low, Charging/ Discharging, Over Load, Short Circuit, Thermal Trip, Solar available/ Not available and PV reverse on LCD Display.
- User- friendly LCD for the display of mode of operation and all parameters.
Technical Specifications
| Model | 650 VA H-UPS | 850 VA H-UPS | 1000 VA H-UPS | 1450 VA H-UPS | 2000 VA H-UPS |
| Nominal Battery Voltage | 12 VDC | 24 VDC | |||
| Solar Panel Connected for 50 Amps PWM/MPPT* Charge Controller (Max.) | 850Wp | 850Wp | 850Wp | 1700wp | 1700Wp |
| AC Mains Mode | |||||
Ac Mains Mode
| Input Voltage Range (Normal Mode) | 100 to 280 VAC ± 5 VAC (Wide Range) | |
| Input Voltage Range (UPS Mode) | 180 to 260 VAC ± VAC | |
| Changeover Time Maximum | <30 ms (in Normal Mode) and < 10 ms (in UPS Mode) | |
| Max. Charging Current (NC) | 10A + 1A | |
| Max. Charging Current (HC) | 10A + 1A | |
| Boost Charging Voltage | 14.4 ± 0.2 VDC | 28.8 ±0.4 VDC |
| Float Charging Voltage | 13.7 ± 0.2 VDC | 27.4 ± 0.4 VDC |
Battery Backup Mode
| Output Voltage at No Load | 220 VAC ± 7 VAC | |
| Output Frequency | 50.0Hz ± 0.5Hz | |
| Output Wave Form (At No Load) | 100% Pure Sine Wave | |
| Battery Low alarm | 10.6 ± 0.2 VDC | 21.2 ± 0.2 VDC |
| Battery Low protection | 10.4 ± 0.2 VDC | 20.8 ± 0.2 VDC |
| Overload (Normal/ UPS) | 120% | |
| Short Circuit (Normal/ UPS) | 300% | |
Charging Mode – SOLAR (MPPT Charge Controller – 40 Amp.)
| Output Voltage at No Load | 220 VAC ± 7 VAC | |
| Output Frequency | 50.0Hz ± 0.5Hz | |
| Output Wave Form (At No Load) | 100% Pure Sine Wave | |
| Battery Low alarm | 10.6 ± 0.2 VDC | 21.2 ± 0.2 VDC |
| Battery Low protection | 10.4 ± 0.2 VDC | 20.8 ± 0.2 VDC |
| Overload (Normal/ UPS) | 120% | |
| Short Circuit (Normal/ UPS) | 300% | |
Multi Color LCD Display Colors
- Yellow Color : For Inverter/ UPS mode. No AC Mains (Utility Power)
- Green Color : When AC mains (Utility Power) is available
- Red Color : In case of any Abnormal Condition
Displaying Parameters
AC mains voltage
O/P Load in %
Battery input voltage
Battery Charging/ Discharging current (Batt. Bar)
Faults Status
- Overload
- PV Reverse
- Short Circuit
- Fuse Trip
- Over Temp (Thermometer)
- Low Battery (Empty ‘Battery’ Blinking)
Inverter Status
Solar availability Status